It is available as assembled board with remote.
The VIRE-FM 01C FM –USB Module is available as ready made assembled board. Its output can be connected to power amplifier or into the amplifier of VCD player, Car stereo etc. The module has the following important features:
Item .No.VIRE-01FV4.0
FM Channels 87.5 – 108 MHz
Song number display
Song selection mode
Auto channel scan and save provision
Digital volume level display
Forward and backward selection
Volume Up /down buttons
The circuit board is available as kits with connecting wires. It is necessary to connect Remote Sensor, USB socket and Amplifier with speaker.
Connections
On the PCB, there are markings for wire connections and wire sets are provided along with the kit. The markings on the back of the PCB indicates:
IR Sensor TSOP 1738 connection
IR Sensor TSOP 1838 connection
Gnd - Ground
OUT - Output of Sensor
VS - ( +5V ) Supply
Connect the wires connected to these points to the sensor:
USB Connection
1. GND
2. DP
3. DM
4. 5V- 5 Volt will be available from the board itself
Output to Amplifier
L – Left channel
G – Ground
R – Right channel
Volume control
Use a 10 K Lin dual volume control between the output lines (L and R) of the module and the amplifier. Set minimum volume (2 to 4) in the module using remote and adjust 10 K pot to get clear sound from the speaker. Then increase the volume using remote to the required level. The module can give 1 to 50 range volume.
Antenna
Antenna is necessary if the signal strength is weak .Connect 30 cm plastic wire to the point ANT on the PCB
5 Volt regulated power supply is necessary for the circuit. Make a regulated power supply with IC 7805 with 1000 uF filter capacitor. If the power supply is not well regulated or with ripples, performance of the circuit will be poor.
Gnd - Ground
OUT - Output of Sensor
VS - ( +5V ) Supply
Connect the wires connected to these points to the sensor:
USB Connection
1. GND
2. DP
3. DM
4. 5V- 5 Volt will be available from the board itself
Output to Amplifier
L – Left channel
G – Ground
R – Right channel
Volume control
Use a 10 K Lin dual volume control between the output lines (L and R) of the module and the amplifier. Set minimum volume (2 to 4) in the module using remote and adjust 10 K pot to get clear sound from the speaker. Then increase the volume using remote to the required level. The module can give 1 to 50 range volume.
Antenna
Antenna is necessary if the signal strength is weak .Connect 30 cm plastic wire to the point ANT on the PCB
5 Volt regulated power supply is necessary for the circuit. Make a regulated power supply with IC 7805 with 1000 uF filter capacitor. If the power supply is not well regulated or with ripples, performance of the circuit will be poor.
Remote less operation
On the PCB, connections V+, M,V-, PP etc are given to connect membrane switches for manual operation.
Key Specifications/Special Features
On the PCB, connections V+, M,V-, PP etc are given to connect membrane switches for manual operation.
Key Specifications/Special Features
- Support MP3, USB and SD
- FM function: 87.5 to 108MHz frequency range
- With 1.888 display
- Accessory: remote
- Power supply: 5V/1A
- Separation: 45dB
- Distortion: 0.1%
- Output: 550MV
- S/N: 65dB
- Frequency response range: 90.5, 106.5 and 98.5Mhz
- Auto-search station: 22 to 28dB
- Packing:
- Inner box: 125 pieces/box
- Inner box dimensions: 28 x 21.5 x 7mm
- Inner box/weight: 1.05kg
- Carton: 20 boxes, 2,500 pieces/carton
- Carton dimensions: 58.5 x 44.5 x 36.5mm
- Carton/weight: 21kg.
Wire Connection diagram
Sir i have this circuit i by mistakenly gave 12v means just like tap not even single second i gave 12v..
ReplyDeletewhich parts will be exhausted?
which parts should be replaced?
entire bord!!!!!!!!!!!!!!!
Deletehello sir note input power supply +5v
DeleteGreat and a very useful blog for me. It contains a lot of useful information's. Thanks a lot for sharing.
ReplyDeletehttp://caskaindia.com
thnxx for the guide sir
ReplyDeletebut can you plzz tell the datasheet of this remote??